For our smart bms, when the first use, need to activate first, then B-P-conductive, BMS can work well.
Method ①: buy the power board and there is an activation switch on the board and click the button.
Method ②: Charge activation, B-Line must be the total negative pole of the battery pack when
3S ~ 5S, J series (10J, 16J) BMS only can be activated by this way.
Touchable screen LCD and bluetooth function won't be working / exist at the same BMS! !!! You can only choose one of them.
Main Features Description:
Over-charge protection: Yes
Over-discharge protection: Yes
Over-current protection: Yes
Temperature protection: Yes
Disconnect protection: Yes
Short circuit protection: Yes
Short circuit protect recover: Yes
Balance function: yes
Benefits:
BMS was made by high quality Mos and IC imported. Keep your battery long cycle life time.
Use top quality (A-level) protective integrated circuit IC, from the solution of Japan.
Extreme low power consumption. The consumption of the whole device is less than 50uA.
PCB use high anti-corrosion, high water resistance, high impedance ESD compliant plating.
Function:
UART: UART is Universal Asynchronous Receiver / Transmitter, it transforms the data transmitted between serial communication and parallel communication. As a chip to convert parallel input signals into serial signals, UART is usually integrated into other communication interfaces. UART cable can support connection bms between PC and you can set the parameters through PC screen.
Bluetooth module: available to connect with Android and IOS App and can check the battery status in real time through mobile phone.
All Parameters can be check Via Bluetooth App or UART USB Connection with PC Monitoring Program. Default setting inside BMS are for Li-ion batteries. But this BMS also can used for any lithium technologies i.e. LiFePo4, Lithium Ion, LTO, LIPO, Lithium Metal and also used for sodium Ion batteries by changing internal parameters after connecting to Bluetooth App or computer. Please note that this BMS can be used for 13S battery pack only. It Cannot be used for any other battery pack Configurations.
Charge and Discharge Protection Current, Voltage, Temperature Can Be Reset in Certain Range.
When Factors Like Temperature, Voltage, Current Cause Damage to Battery , There Will be Alarm Display on Bluetooth Smart BMS
Product Description:
This is a Daly Smart BMS Rated 3.7V Smart communication management system. The Battery pack strings must be equal to BMS strings. DALY BMS can be applied with Home storage power, RV power supply and other lithium devices.
16S 50AMP 48 V LiFePo4 lithium iron ferro phosphate LFP BMS.
BMS have balancing and temperature control functions.
BMS having a function of proper higher and lower cutoff.
It is in a size which is suitable for many applications requiring high integration and low cost. It can meet various performance requirements and ensure the absolute safety and reliability of the battery pack.
Over charge protection, over discharge protection function, short circuit protection function, over current protection function, balance.
Low internal resistance, high power MOS. MOS transistor can control the battery charge and discharge, low standby current consumption.
The power range described is applicable to the following products: vacuum cleaner, massager battery pack, LED light backup power supply, electronic products, solar street light battery pack, monitoring standby power supply, etc.
This is DALY smart bms Rated 3.2V 15S 100A with smart communication function (CAN) Battery pack strings must be matched with BMS strings. DALY BMS Adopt top quality (A-level) IC Solution make battery management much more efficient , greatly help to keep battery pack healthy and stable. Extending battery life-span, improve performance. DALY BMS being waterproof test, humidity resistance . DALY BMS can be applied with home power storage system , RV Power supply , E-bike and other lithium battery related device . Factory Default Setting Over Charge detect voltage: 3.75±0.05 Over Charge release voltage: 3.65±0.05 Over Charge protection delay 1s Balance detect Voltage: 3.2V Balance Current: 35±5 mA Over discharge voltage detect :2.2±0.1 V Over Discharge Detect delay 1s Over discharge voltage release voltage: 2.3±0.1 V BMS Self-Consumption Working Current :≤20 ma
Daly Lifepo4 Smart 23S 72V 40A Waterproof Battery Management System
Brand
Daly
Board Type
Single Sided
Material
PCB With Aluminum heat Shink
Usage/Application
E-Rickshaw, E-scooter, E-Bicycle
Size
125X64X10mm
Type Of Tension
DC
Weight
0.175kg
I Deal In
New Only
Volatage for Lithium Ferro Phosphate
72 V
OVER CHARGE PROTECTION
yes
OVER DISCHARGE PROTECTION
yes
SHORT CIRCUIT PROTECTION
yes
Voltage
72 V
Ampere
40Amp
Single Over Charge Protection and Release Voltage
Yes
Environmental Compliance
Yes
Continuous Current
40Amp
Lower Cutoff
62.1
Higher Cutoff
82.8
NTC
Yes
Balancing
Passive
Material Type
PCB With Aluminum Heat Sink
Temperature
-40C 80C
Minimum Order Quantity
1
Product Description23S 40AMP 72V LiFePo4 lithium iron ferro phosphate LFP BMS. BMS have balancing and temperature control functions. BMS having a function of proper higher and lower cutoff.
The DALY LiFePO4 Smart BMS 16S 48V 100A Waterproof Battery Management System is designed for managing lithium iron phosphate battery packs. Here’s an overview of its specifications and features:
Key Specifications:
Configuration:
Series: 16S (16 cells in series)
Nominal Voltage: 48V (with each LiFePO4 cell nominally at 3.2V)
Current Ratings:
Continuous Discharge Current: 100A
Peak Discharge Current: Typically higher for short bursts (specific values should be confirmed in the datasheet).
Balancing:
Cell Balancing: Active or passive balancing, depending on the model, to ensure even charge distribution among cells.
Protection Features:
Over-Voltage Protection (OVP): Prevents damage from excessive voltage.
Under-Voltage Protection (UVP): Protects against excessive discharge.
Over-Current Protection (OCP): Protects against high current draw.
Short-Circuit Protection: Cuts off the output in case of a short circuit.
Temperature Monitoring: Built-in sensors to monitor cell temperatures, with cut-off points for safety.
Communication:
Smart Features: Often includes Bluetooth or UART communication for monitoring through a smartphone app or computer.
Real-time Data: Provides information on cell voltages, temperature, and overall pack status.
Waterproof Rating:
Typically rated at IP67, providing protection against dust and water immersion.
16S 80AMP 48 V LiFePo4 lithium iron ferro phosphate LFP BMS.
BMS have balancing and temperature control functions.
BMS having a function of proper higher and lower cutoff.
It is in a size which is suitable for many applications requiring high integration and low cost. It can meet various performance requirements and ensure the absolute safety and reliability of the battery pack.
Over charge protection, over discharge protection function, short circuit protection function, over current protection function, balance.
Low internal resistance, high power MOS. MOS transistor can control the battery charge and discharge, low standby current consumption.
The power range described is applicable to the following products: vacuum cleaner, massager battery pack, LED light backup power supply, electronic products, solar street light battery pack, monitoring standby power supply, etc.
DALY Smart BMS 20S 72V 40A Li-ion with Bluetooth dongle
DALY BMS used for 18650, 26650, 21700, prismatic cells etc.
Bullet points:
All Parameters can be check Via Bluetooth App or UART USB Connection with PC Monitoring Program. Default setting inside BMS are for Li-ion batteries. But this BMS can also be used for any lithium technologies i.e. LiFePo4, Lithium Ion, LTO, LIPO, Lithium Metal and also used for sodium Ion batteries by changing internal parameters after connecting to Bluetooth App or computer. Please note that this BMS can be used for 20S battery pack only. It Cannot be used for any other battery pack Configurations.
Charge and Discharge Protection Current, Voltage, Temperature Can Be Reset in Certain Range.
When Factors Like Temperature, Voltage, Current Cause Damage to Battery There Will be Alarm Display on Bluetooth Smart BMS APP.
Box contains: Rated voltage 72V Smart BMS (With smart communication function), Bluetooth dongle, Temperature sensor, Suitable Connecting leads (21 Wire sense cable with connector), USB-UART cable and Instruction sheet.
USA Seller with Fast delivery.
It is used for any lithium battery applications including solar, RV, Electric bikes, Skate board, camping, Boat, Power tools, Lawn moving and household energy storage systems.
Product Description:
This is a Daly Smart BMS Rated 3.7V Smart communication management system. The Battery pack strings must be equal to BMS strings. DALY BMS can be applied with Home storage power, RV power supply and other lithium devices. DALY BMS is top quality IC solution make battery more efficient, healthy and stable condition.
Daly Lfp Smart Bms 19s 80amp Same Port Waterproof, For Battery Management System
It is in a size which is suitable for many applications requiring high integration and low cost. It can meet various performance requirements and ensure the absolute safety and reliability of the battery pack.
Over charge protection, over discharge protection function, short circuit protection function, over current protection function, balance.
Low internal resistance, high power MOS. MOS transistor can control the battery charge and discharge, low standby current consumption.
The power range described is applicable to the following products: vacuum cleaner, massager battery pack, LED light backup power supply, electronic products, solar street light battery pack, monitoring standby power supply, etc.1S-2Amp,1S-3Amp,1S-4Amp,1S-5Amp,
